ÔÚLinuxÉÏ°²×°Broadcom NetXtreme BCM5704 Gigabit Íø¿¨

¹²ÓÐ 1 ÌõÆÀÂÛ

1. redfans ÓÚ 2008-03-17 15:48:43·¢±í:

   ¸½£ºREADME.txtÎļþÄÚÈÝ
   
   

   ����:

   Installation Notes
   Broadcom tg3 Linux Driver
   Version 3.81c
   09/18/2007
   
   Broadcom Corporation
   5300 California Avenue
   Irvine, California 92617
   
   Copyright (c) 2004, 2005, 2006, 2007 Broadcom Corporation
   All rights reserved
   
   
   Table of Contents
   =================
   
   Introduction
   Limitations
   Packaging
   Installing Source RPM Package
   Building Driver From TAR File
   Driver Settings
   Driver Defaults
   Unloading and Removing Driver
   Driver Messages
   
   
   Introduction
   ============
   
   This file describes the tg3 Linux driver for the Broadcom NetXtreme
   10/100/1000 Mbps PCI/PCI-X/PCI Express Ethernet Network Controllers.
   The latest driver is in the latest 2.6 Linux kernel. It can also be
   downloaded from http://www.broadcom.com as a source package, but is
   generally not necessary to do so if you are using the latest 2.6
   upstream kernel from http://www.kernel.org or one of the latest
   vendor kernels from Red Hat, SuSE, or others.
   
   The tg3 driver from the Broadcom package is almost identical to the
   tg3 driver in the latest 2.6 upstream Linux kernel. It includes some
   additional kernel compatible code to allow it to compile on older 2.6
   and some 2.4 kernels. The version number is also similar but generally
   has a one letter suffix at the end, (e.g. 3.55b) to distinguish it from
   the in-kernel tg3 driver.
   
   The next few sections on packaging, compiling, and installation apply
   mostly to the Broadcom driver package only.
   
   
   Limitations
   ===========
   
   The current version of the driver has been tested on 2.4.x kernels starting
   from 2.4.24 and all 2.6.x kernels. The driver may not compile on kernels
   older than 2.4.24. Testing is concentrated on i386 and x86_64 architectures.
   Only limited testing has been done on some other architectures such as
   powerpc and sparc64.
   
   Minor changes to some source files and Makefile may be needed on some
   kernels.
   
   
   Packaging
   =========
   
   To replace an older previously installed or in-kernel tg3 driver, follow
   the instructions below.
   
   The driver package from http://www.broadcom.com is released in two packaging
   formats: source RPM and compressed tar formats. The file names for the two
   packages are tg3-.src.rpm and tg3-.tar.gz respectively.
   Identical source files to build the driver are included in both packages.
   
   
   Installing Source RPM Package
   =============================
   
   The following are general guidelines for installing the driver.
   
   1. Install the source RPM package:
   
   rpm -ivh tg3-.src.rpm
   
   2. CD to the RPM path and build the binary driver for your kernel:
   
   cd /usr/src/{redhat,OpenLinux,turbo,packages,rpm ..}
   
   rpm -bb SPECS/tg3.spec
   
   or
   
   rpmbuild -bb SPECS/tg3.spec (for RPM version 4.x.x)
   
   Note that the RPM path is different for different Linux distributions.
   
   The driver will be compiled for the running kernel by default. To build
   the driver for a kernel different than the running one, specify the
   kernel by defining it in KVER:
   
   rpmbuild -bb SPECS/tg3.spec --define "KVER "
   
   where in the form of 2.x.y-z is the version of another
   kernel that is installed on the system.
   
   3. Install the newly built package (driver and man page):
   
   rpm -ivh RPMS//tg3-..rpm
   
   is the architecture of the machine, e.g. i386:
   
   rpm -ivh RPMS/i386/tg3-.i386.rpm
   
   Note that the --force option may be needed on some Linux distributions
   if conflicts are reported.
   
   The driver will be installed in the following path:
   
   2.4.x kernels:
   
   /lib/modules//kernel/drivers/net/tg3.o
   
   2.6.x kernels:
   
   /lib/modules//kernel/drivers/net/tg3.ko
   
   4. Load the driver:
   
   insmod tg3.o
   or
   insmod tg3.ko (on 2.6.x kernels)
   or
   modprobe tg3
   
   5. To configure network protocol and address, refer to various Linux
   documentations.
   
   
   Building Driver From TAR File
   =============================
   
   The following are general guidelines for installing the driver.
   
   1. Create a directory and extract the files:
   
   tar xvzf tg3-.tar.gz
   
   2. Build the driver tg3.o (or tg3.ko) as a loadable module for the
   running kernel:
   
   cd src
   make
   
   The driver will be compiled for the running kernel by default. To build
   the driver for a kernel different than the running one, specify the
   kernel by defining it in KVER:
   
   make KVER=
   
   where in the form of 2.x.y-z is the version of another
   kernel that is installed on the system.
   
   3. Test the driver by loading it:
   
   insmod tg3.o
   or
   insmod tg3.ko (on 2.6.x kernels)
   or
   insmod tg3
   
   4. Install the driver:
   
   make install
   
   See RPM instructions above for the location of the installed driver.
   
   5. To configure network protocol and address, refer to various Linux
   documentations.
   
   
   Driver Settings
   ===============
   
   This and the rest of the sections below apply to both the in-kernel tg3
   driver and the tg3 driver package from Broadcom.
   
   Driver settings can be queried and changed using ethtool. The latest ethtool
   can be downloaded from http://sourceforge.net/projects/gkernel if it is not
   already installed. The following are some common examples on how to use
   ethtool. See the ethtool man page for more information. ethtool settings do
   not persist across reboot or module reload. The ethtool commands can be put
   in a startup script such as /etc/rc.local to preserve the settings across a
   reboot. On Red Hat distributions, "ethtool -s" parameters can be specified
   in the ifcfg-ethx scripts using the ETHTOOL_OPTS keyword. The specified
   ethtool parameters will be set during ifup. Example:
   /etc/sysconfig/network-scripts/ifcfg-eth0:
   
   ETHTOOL_OPTS="wol g speed 100 duplex half autoneg off"
   
   Some ethtool examples:
   
   1. Show current speed, duplex, and link status:
   
   ethtool eth0
   
   2. Change speed, duplex, autoneg:
   
   Example: 100Mbps half duplex, no autonegotiation:
   
   ethtool -s eth0 speed 100 duplex half autoneg off
   
   Example: Autonegotiation with full advertisement:
   
   ethtool -s eth0 autoneg on
   
   Example: Autonegotiation with 100Mbps full duplex advertisement only:
   
   ethtool -s eth0 speed 100 duplex full autoneg on
   
   3. Show flow control settings:
   
   ethtool -a eth0
   
   4. Change flow control settings:
   
   Example: Turn off flow control
   
   ethtool -A eth0 autoneg off rx off tx off
   
   Example: Turn flow control autonegotiation on with tx and rx advertisement:
   
   ethtool -A eth0 autoneg on rx on tx on
   
   Note that this is only valid if speed is set to autonegotiation.
   
   5. Show offload settings:
   
   ethtool -k eth0
   
   6. Change offload settings:
   
   Example: Turn off TSO (TCP segmentation offload)
   
   ethtool -K eth0 tso off
   
   7. Get statistics:
   
   ethtool -S eth0
   
   8. Perform self-test:
   
   ethtool -t eth0
   
   Note that the interface (eth0) must be up to do all tests.
   
   9. See ethtool man page for more options.
   
   
   Driver Defaults
   ===============
   
   Speed : Autonegotiation with all speeds advertised
   
   Flow control : Autonegotiation with rx and tx advertised
   
   MTU : 1500 (range 46 - 9000)
   
   Some chips do not support jumbo MTUs bigger than
   1500
   
   Rx Ring Size : 200 (range 0 - 511)
   
   Some chips are fixed at 64
   
   Rx Jumbo Ring Size : 100 (range 0 - 255)
   
   Not all chips support the jumbo ring, and some
   chips that support jumbo frames do not use the
   jumbo ring.
   
   Tx Ring Size : 511 (range (MAX_SKB_FRAGS+1) - 511)
   
   MAX_SKB_FRAGS varies on different kernels and
   different architectures. On a 2.6 kernel for
   x86, MAX_SKB_FRAGS is 18.
   
   Coalesce rx usecs : 20 (range 0 - 1023)
   
   Coalesce rx usecs irq : 20 (range 0 - 255)
   
   Coalesce rx frames : 5 (range 0 - 1023)
   
   Coalesce rx frames irq : 5 (range 0 - 255)
   
   Coalesce tx usecs : 72 (range 0 - 1023)
   
   Coalesce tx usecs irq : 20 (range 0 - 255)
   
   Coalesce tx frames : 53 (range 0 - 1023)
   
   Coalesce tx frames irq : 5 (range 0 - 255)
   
   Coalesce stats usecs : 1000000 (aprox. 1 sec.)
   
   Some coalescing parameters are not used or have
   different defaults on some chips
   
   MSI : Enabled (if supported by the chip and passed
   the interrupt test)
   
   TSO : Enabled on newer chips that support TCP segmentation
   offload in hardware
   
   WoL : Disabled
   
   
   Unloading and Removing Driver
   =============================
   
   To unload the driver, use ifconfig to bring down all eth# interfaces opened
   by the driver, then do the following:
   
   rmmod tg3
   
   Note that on 2.6 kernels, it is not necessary to bring down the eth#
   interfaces before unloading the driver module.
   
   
   If the driver was installed using rpm, do the following to remove it:
   
   rpm -e tg3
   
   
   If the driver was installed using make install from the tar file, the driver
   tg3.o (or tg3.ko) has to be manually deleted from the system. Refer
   to the section "Installing Source RPM Package" for the location of the
   installed driver.
   
   
   Driver Messages
   ===============
   
   The following are the most common sample messages that may be logged in the file
   /var/log/messages. Use dmesg -n to control the level at which messages
   will appear on the console. Most systems are set to level 6 by default. To see
   all messages, set the level higher.
   
   Driver signon:
   -------------
   
   tg3.c:v3.81c (September 18, 2007)
   
   
   NIC detected:
   ------------
   
   eth0: Tigon3 [partno(BCM95704A6) rev 2003 PHY(5704)] (PCIX:100MHz:64-bit) 10/100/1000Base-T Ethernet 00:10:18:04:3f:36
   eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1]
   eth0: dma_rwctrl[769f4000] dma_mask[64-bit]
   
   
   Link up and speed indication:
   ----------------------------
   
   tg3: eth0: Link is up at 1000 Mbps, full duplex.
   tg3: eth0: Flow control is on for TX and on for RX.
   
   
   Link down indication:
   --------------------
   
   tg3: eth0: Link is down.