shrimp12345 于 2007-07-21 19:30:52发表:
我也是刚才搞好，菜单的网络窗口中你什么也别设置。 下载个rp-pppoe-3.8.tar.tar，然后按照下面的方法来做就可以了。 1.下载rp-pppoe-3.5 2。解压和安装： #tar zxvf rp-pppoe-3.5.tar.gz 进入解压目录执行 #sh ./go 3。配置 然后再来设置ADSL。这一处，我们要用命令。 #adsl-setup Welcome to the Roaring Penguin ADSL client setup. First, I will run some checks on your system to make sure the PPPoE client is installed properly... Looks good! Now, please enter some information: USER NAME >>> Enter your PPPoE user name (default XXX): 在这里输入ADSL的用户名 INTERFACE >>> Enter the Ethernet interface connected to the ADSL modem For Solaris, this is likely to be something like /dev/hme0. For Linux, it will be ethn, where 'n' is a number. (default eth0):如果一张网卡就设置写上eth0 Do you want the link to come up on demand, or stay up continuously? If you want it to come up on demand, enter the idle time in seconds after which the link should be dropped. If you want the link to stay up permanently, enter 'no' (two letters, lower-case.) NOTE: Demand-activated links do not interact well with dynamic IP addresses. You may have some problems with demand-activated links. >>> Enter the demand value (default no):不用写什么 DNS Please enter the IP address of your ISP's primary DNS server. If your ISP claims that 'the server will provide DNS addresses', enter 'server' (all lower-case) here. If you just press enter, I will assume you know what you are doing and not modify your DNS setup. >>> Enter the DNS information here:在这里写上202.96.134.133 下一个DNS是202.96.168.68 //这里根据个人不同可以修改 PASSWORD >>> Please enter your PPPoE password:输入密码 >>> Please re-enter your PPPoE password:再输入一次 FIREWALLING Please choose the firewall rules to use. Note that these rules are very basic. You are strongly encouraged to use a more sophisticated firewall setup; however, these will provide basic security. If you are running any servers on your machine, you must choose 'NONE' and set up firewalling yourself. Otherwise, the firewall rules will deny access to all standard servers like Web, e-mail, ftp, etc. If you are using SSH, the rules will block outgoing SSH connections which allocate a privileged source port. The firewall choices are: 0 - NONE: This script will not set any firewall rules. You are responsible for ensuring the security of your machine. You are STRONGLY recommended to use some kind of firewall rules. 1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation 2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway for a LAN >>> Choose a type of firewall (0-2):这里添写为2 ** Summary of what you entered ** Ethernet Interface: eth0 User name: XXX Activate-on-demand: No DNS: Do not adjust Firewalling: MASQUERADE >>> Accept these settings and adjust configuration files (y/n)? 弄完后，就按一个y键。 不要急于连接,REBOOT -N 然后进入网络设置,设置ETH1固定IP，停止ETH1(我的是用他) 然后ADSL-START PING 你的DNS,如果可以,那么,恭喜你! 如果不行，REBOOT -N ADSL-START,这下没问题啦，尽情享受吧！
yorktown 于 2007-07-21 17:14:09发表:
这个我以前试过了 不怎么顶用啊！！！！！不过还是谢谢！
rmidable 于 2007-07-16 21:30:21发表:
这个是搜索的结果，也是F7里的 修改/boot/grub/grub.conf kernel /boot/vmlinuz-2.6.21-1.3194.fc7 ro root=LABEL=/ apm=on apm=power-off rhgb quiet 如上，加入apm=on apm=power-off 重新启动就ok了。
shrimp12345 于 2007-07-21 19:30:52发表:
我也是刚才搞好，菜单的网络窗口中你什么也别设置。
下载个rp-pppoe-3.8.tar.tar，然后按照下面的方法来做就可以了。
1.下载rp-pppoe-3.5
2。解压和安装：
#tar zxvf rp-pppoe-3.5.tar.gz
进入解压目录执行
#sh ./go
3。配置
然后再来设置ADSL。这一处，我们要用命令。
#adsl-setup
Welcome to the Roaring Penguin ADSL client setup. First, I will run
some checks on your system to make sure the PPPoE client is installed
properly...
Looks good! Now, please enter some information:
USER NAME
>>> Enter your PPPoE user name (default XXX): 在这里输入ADSL的用户名
INTERFACE
>>> Enter the Ethernet interface connected to the ADSL modem
For Solaris, this is likely to be something like /dev/hme0.
For Linux, it will be ethn, where 'n' is a number.
(default eth0):如果一张网卡就设置写上eth0
Do you want the link to come up on demand, or stay up continuously?
If you want it to come up on demand, enter the idle time in seconds
after which the link should be dropped. If you want the link to
stay up permanently, enter 'no' (two letters, lower-case.)
NOTE: Demand-activated links do not interact well with dynamic IP
addresses. You may have some problems with demand-activated links.
>>> Enter the demand value (default no):不用写什么
DNS
Please enter the IP address of your ISP's primary DNS server.
If your ISP claims that 'the server will provide DNS addresses',
enter 'server' (all lower-case) here.
If you just press enter, I will assume you know what you are
doing and not modify your DNS setup.
>>> Enter the DNS information here:在这里写上202.96.134.133
下一个DNS是202.96.168.68 //这里根据个人不同可以修改
PASSWORD
>>> Please enter your PPPoE password:输入密码
>>> Please re-enter your PPPoE password:再输入一次
FIREWALLING
Please choose the firewall rules to use. Note that these rules are
very basic. You are strongly encouraged to use a more sophisticated
firewall setup; however, these will provide basic security. If you
are running any servers on your machine, you must choose 'NONE' and
set up firewalling yourself. Otherwise, the firewall rules will deny
access to all standard servers like Web, e-mail, ftp, etc. If you
are using SSH, the rules will block outgoing SSH connections which
allocate a privileged source port.
The firewall choices are:
0 - NONE: This script will not set any firewall rules. You are responsible
for ensuring the security of your machine. You are STRONGLY
recommended to use some kind of firewall rules.
1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway
for a LAN
>>> Choose a type of firewall (0-2):这里添写为2
** Summary of what you entered **
Ethernet Interface: eth0
User name: XXX
Activate-on-demand: No
DNS: Do not adjust
Firewalling: MASQUERADE
>>> Accept these settings and adjust configuration files (y/n)?
弄完后，就按一个y键。
不要急于连接,REBOOT -N
然后进入网络设置,设置ETH1固定IP，停止ETH1(我的是用他)
然后ADSL-START
PING 你的DNS,如果可以,那么,恭喜你!
如果不行，REBOOT -N
ADSL-START,这下没问题啦，尽情享受吧！
yorktown 于 2007-07-21 17:14:09发表:
这个我以前试过了 不怎么顶用啊！！！！！不过还是谢谢！
rmidable 于 2007-07-16 21:30:21发表:
这个是搜索的结果，也是F7里的
修改/boot/grub/grub.conf
kernel /boot/vmlinuz-2.6.21-1.3194.fc7 ro root=LABEL=/ apm=on apm=power-off rhgb quiet
如上，加入apm=on apm=power-off 重新启动就ok了。