在线等啊急大家给我看看啊！我怎么上不了网哦我的是拨号上网

Welcome to the ADSL client setup. First, I will run some checks on
your system to make sure the PPPoE client is installed properly...

The following DSL config was found on your system:

Device: Name:
ppp0 DSLppp0

Please enter the device if you want to configure the present DSL config
(default ppp0) or enter 'n' if you want to create a new one: y
Device 'y' is not found in the list, please choose the correct one
Please enter the device if you want to configure the present DSL config
(default ppp0) or enter 'n' if you want to create a new one: n

LOGIN NAME

Enter your Login Name: RDG8588@ls

INTERFACE

Enter the Ethernet interface connected to the ADSL modem
For Solaris, this is likely to be something like /dev/hme0.
For Linux, it will be ethX, where 'X' is a number.
(default eth0):eth0
Do you want the link to come up on demand, or stay up continuously?
If you want it to come up on demand, enter the idle time in seconds
after which the link should be dropped. If you want the link to
stay up permanently, enter 'no' (two letters, lower-case.)
NOTE: Demand-activated links do not interact well with dynamic IP
addresses. You may have some problems with demand-activated links.
Enter the demand value (default no): no

DNS

Please enter the IP address of your ISP's primary DNS server.
If your ISP claims that 'the server will provide dynamic DNS addresses',
enter 'server' (all lower-case) here.
If you just press enter, I will assume you know what you are
doing and not modify your DNS setup.
Enter the DNS information here: server

PASSWORD

Please enter your Password:666666
Please re-enter your Password: 666666

USERCTRL

Please enter 'yes' (two letters, lower-case.) if you want to allow
normal user to start or stop DSL connection (default yes): yes

FIREWALLING

Please choose the firewall rules to use. Note that these rules are
very basic. You are strongly encouraged to use a more sophisticated
firewall setup; however, these will provide basic security. If you
are running any servers on your machine, you must choose 'NONE' and
set up firewalling yourself. Otherwise, the firewall rules will deny
access to all standard servers like Web, e-mail, ftp, etc. If you
are using SSH, the rules will block outgoing SSH connections which
allocate a privileged source port.

The firewall choices are:
0 - NONE: This script will not set any firewall rules. You are responsible
for ensuring the security of your machine. You are STRONGLY
recommended to use some kind of firewall rules.
1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway
for a LAN
Choose a type of firewall (0-2): 0

Start this connection at boot time

Do you want to start this connection at boot time?
Please enter no or yes (default no):no

** Summary of what you entered **

Ethernet Interface: etho
User name: RDG8588@ls
Activate-on-demand: No
DNS addresses: Supplied by ISP's server
Firewalling: NONE
User Control: yes
Accept these settings and adjust configuration files (y/n)? y
Adjusting /etc/sysconfig/network-scripts/ifcfg-ppp1
Adjusting /etc/ppp/chap-secrets and /etc/ppp/pap-secrets
(But first backing it up to /etc/ppp/chap-secrets.bak)
(But first backing it up to /etc/ppp/pap-secrets.bak)



Congratulations, it should be all set up!

Type '/sbin/ifup ppp1' to bring up your xDSL link and '/sbin/ifdown ppp1'
to bring it down.
Type '/sbin/adsl-status /etc/sysconfig/network-scripts/ifcfg-ppp1'
to see the link status.

You have new mail in /var/spool/mail/root
[root@localhost rp-pppoe-3.8]# /usr/sbin/adsl-start
[root@localhost rp-pppoe-3.8]# cd /
[root@localhost /]# /usr/sbin/adsl-start
[root@localhost /]# ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:00:E8:62:F2:10
inet addr:192.168.1.2 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:977 errors:0 dropped:0 overruns:0 frame:0
TX packets:767 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:59182 (57.7 Kb) TX bytes:44737 (43.6 Kb)
Interrupt:11 Base address:0x8000