redhat linux5拨号上网求助

共有 5 条评论

1. hantu 于 2009-04-07 23:18:46发表:

   安装并配置rp-pppoe软件即可

2. 1234qw 于 2009-04-04 17:17:17发表:

   http://www.cdgwbn.net.cn/news/show.aspx?id=495&cid=28

3. lywqjhxsl 于 2009-04-04 01:44:33发表:

   没弄过,帮你定一下,如果是虚拟机的,直接NAT的就行了

4. qrpengx 于 2009-04-03 23:17:41发表:

   adsl-setup　 ← 建立ADSL连接
   
   
   Welcome to the ADSL client setup. First, I will run some checks on
   your system to make sure the PPPoE client is installed properly...
   
   
   LOGIN NAME
   
   Enter your Login Name (default root):　← 填入ADSL连接的用户名
   
   INTERFACE
   
   Enter the Ethernet interface connected to the ADSL modem
   For Solaris, this is likely to be something like /dev/hme0.
   For Linux, it will be ethX, where 'X' is a number.
   (default eth0):　　← 指定网络接入设备，一块网卡的情况下，一般为默认eth0
   
   Do you want the link to come up on demand, or stay up continuously?
   If you want it to come up on demand, enter the idle time in seconds
   after which the link should be dropped. If you want the link to
   stay up permanently, enter 'no' (two letters, lower-case.)
   NOTE: Demand-activated links do not interact well with dynamic IP
   addresses. You may have some problems with demand-activated links.
   Enter the demand value (default no):　　← 直接按回车，接受默认设置
   
   DNS
   
   Please enter the IP address of your ISP's primary DNS server.
   If your ISP claims that 'the server will provide dynamic DNS addresses',
   enter 'server' (all lower-case) here.
   If you just press enter, I will assume you know what you are
   doing and not modify your DNS setup.
   Enter the DNS information here:　　← 如果知道DNS服务器的信息在此填入。不知道的情况按回车跳过
   
   PASSWORD
   
   Please enter your Password:　← 输入ADSL的连接密码
   Please re-enter your Password:　← 再次确认输入ADSL的连接密码
   
   USERCTRL
   
   Please enter 'yes' (two letters, lower-case.) if you want to allow
   normal user to start or stop DSL connection (default yes): no　← 填入no，不允许一般用户控制PPPoE的连接
   
   FIREWALLING
   
   Please choose the firewall rules to use. Note that these rules are
   very basic. You are strongly encouraged to use a more sophisticated
   firewall setup; however, these will provide basic security. If you
   are running any servers on your machine, you must choose 'NONE' and
   set up firewalling yourself. Otherwise, the firewall rules will deny
   access to all standard servers like Web, e-mail, ftp, etc. If you
   are using SSH, the rules will block outgoing SSH connections which
   allocate a privileged source port.
   
   The firewall choices are:
   0 - NONE: This script will not set any firewall rules. You are responsible
   for ensuring the security of your machine. You are STRONGLY
   recommended to use some kind of firewall rules.
   1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
   2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway
   for a LAN
   Choose a type of firewall (0-2): 0　← 输入0，不在这里使用防火墙
   
   Start this connection at boot time
   
   Do you want to start this connection at boot time?
   Please enter no or yes (default no): yes　← 填入yes，在系统启动时自动连接ADSL
   
   ** Summary of what you entered **
   
   Ethernet Interface: eth0
   User name: caun870293@ca.dti.ne.jp
   Activate-on-demand: No
   DNS: Do not adjust
   Firewalling: NONE
   User Control: no
   Accept these settings and adjust configuration files (y/n)? y　← 配置信息确认无误后，键入y同意设置
   Adjusting /etc/sysconfig/network-scripts/ifcfg-ppp0
   Adjusting /etc/ppp/chap-secrets and /etc/ppp/pap-secrets
   (But first backing it up to /etc/ppp/chap-secrets.bak)
   (But first backing it up to /etc/ppp/pap-secrets.bak)
   
   ?
   
   Congratulations, it should be all set up!
   
   Type '/sbin/ifup ppp0' to bring up your xDSL link and '/sbin/ifdown ppp0'
   to bring it down.
   Type '/sbin/adsl-status /etc/sysconfig/network-scripts/ifcfg-ppp0'
   to see the link status.
   [root@sample ~]# adsl-start 　← 启动ADSL连接
   
   [root@sample ~]# 　　← 稍等片刻后若启动成功后出现提示符（无任何提示即意味着连接成功）

5. 刘冲 于 2009-04-03 12:53:30发表:

   我也不懂，但是我直接把上网帐号密码存在猫上，联网安装redhat后自动设置就能上网了。