求：arm linux 启动到shell登录前崩溃，如何分析？

目前在调的新板子，arm linux 启动到shell 登录前崩溃，相关信息如下。请各位帮忙分析可能的原因？
cpu：arm cortex A9 4核 800Mhz
内存：1GB DDR3
存储：nand flash 4GB
## Booting kernel from Legacy Image at 10800000 ...
Image Name: Linux-3.0.35-2666-gbdde708
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3830608 Bytes = 3.7 MB
Load Address: 10008000
Entry Point: 10008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

Linux version 3.0.35-2666-gbdde708 (huangwf@mydev-s) (gcc version 4.6.2 20110630 (prerelease) (Freescale MAD -- Linaro 2011.07 -- Built at 2011/08/10 09:20) ) #3 SMP PREEMPT Wed Jul 23 19:21:11 CST 2014
CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: Freescale i.MX 6Quad/DualLite/Solo Sabre Auto Board
Memory policy: ECC disabled, Data cache writealloc
CPU identified as i.MX6Q, silicon rev 1.2
PERCPU: Embedded 7 pages/cpu @8c008000 s5440 r8192 d15040 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 227328
Kernel command line: noinitrd console=ttymxc1,115200n8 ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs rootwait rw mtdparts=gpmi-nand:16m(boot),16m(kernel),128m(rootfs)
PID hash table entries: 4096 (order: 2, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 640MB 256MB = 896MB total
Memory: 896904k/896904k available, 151672k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xf4600000 - 0xffe00000 ( 184 MB)
vmalloc : 0xc0800000 - 0xf2000000 ( 792 MB)
lowmem : 0x80000000 - 0xc0000000 (1024 MB)
pkmap : 0x7fe00000 - 0x80000000 ( 2 MB)
modules : 0x7f000000 - 0x7fe00000 ( 14 MB)
.init : 0x80008000 - 0x8003a000 ( 200 kB)
.text : 0x8003a000 - 0x80a8048c (10522 kB)
.data : 0x80a82000 - 0x80ae2760 ( 386 kB)
.bss : 0x80ae2784 - 0x80b305ec ( 312 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Preemptible hierarchical RCU implementation.
NR_IRQS:624
MXC GPIO hardware
sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms
arm_max_freq=1GHz
MXC_Early serial console at MMIO 0x21e8000 (options '115200n8')
bootconsole [ttymxc1] enabled
Console: colour dummy device 80x30
Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
calling init_hw_perf_events+0x0/0x170 @ 1
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
initcall init_hw_perf_events+0x0/0x170 returned 0 after 9765 usecs
calling migration_init+0x0/0x80 @ 1
initcall migration_init+0x0/0x80 returned 0 after 0 usecs
calling spawn_ksoftirqd+0x0/0x60 @ 1
initcall spawn_ksoftirqd+0x0/0x60 returned 0 after 19531 usecs
calling init_workqueues+0x0/0x38c @ 1
initcall init_workqueues+0x0/0x38c returned 0 after 0 usecs
calling cpu_stop_init+0x0/0xcc @ 1
initcall cpu_stop_init+0x0/0xcc returned 0 after 19531 usecs
calling rcu_scheduler_really_started+0x0/0x18 @ 1
initcall rcu_scheduler_really_started+0x0/0x18 returned 0 after 0 usecs
CPU1: Booted secondary processor
CPU2: Booted secondary processor
CPU3: Booted secondary processor
Brought up 4 CPUs
SMP: Total of 4 processors activated (6324.22 BogoMIPS).
calling init_mmap_min_addr+0x0/0x20 @ 1
initcall init_mmap_min_addr+0x0/0x20 returned 0 after 0 usecs
calling init_cpufreq_transition_notifier_list+0x0/0x24 @ 1
initcall init_cpufreq_transition_notifier_list+0x0/0x24 returned 0 after 0 usecs
calling net_ns_init+0x0/0x1a8 @ 1
initcall net_ns_init+0x0/0x1a8 returned 0 after 0 usecs
calling ptrace_break_init+0x0/0x2c @ 1
initcall ptrace_break_init+0x0/0x2c returned 0 after 0 usecs
calling twd_cpufreq_init+0x0/0x60 @ 1
initcall twd_cpufreq_init+0x0/0x60 returned 0 after 0 usecs
calling consistent_init+0x0/0xc8 @ 1
initcall consistent_init+0x0/0xc8 returned 0 after 0 usecs
calling v6_userpage_init+0x0/0x8 @ 1
initcall v6_userpage_init+0x0/0x8 returned 0 after 0 usecs
calling cpu_hotplug_pm_sync_init+0x0/0x18 @ 1
initcall cpu_hotplug_pm_sync_init+0x0/0x18 returned 0 after 0 usecs
calling alloc_frozen_cpus+0x0/0x8 @ 1
initcall alloc_frozen_cpus+0x0/0x8 returned 0 after 0 usecs
calling sysctl_init+0x0/0x3c @ 1
initcall sysctl_init+0x0/0x3c returned 0 after 0 usecs
calling ksysfs_init+0x0/0x98 @ 1
initcall ksysfs_init+0x0/0x98 returned 0 after 0 usecs
calling init_jiffies_clocksource+0x0/0xc @ 1
initcall init_jiffies_clocksource+0x0/0xc returned 0 after 0 usecs
calling pm_init+0x0/0x78 @ 1
initcall pm_init+0x0/0x78 returned 0 after 0 usecs
calling init_zero_pfn+0x0/0x38 @ 1
initcall init_zero_pfn+0x0/0x38 returned 0 after 0 usecs
calling fsnotify_init+0x0/0x24 @ 1
initcall fsnotify_init+0x0/0x24 returned 0 after 0 usecs
calling filelock_init+0x0/0x44 @ 1
initcall filelock_init+0x0/0x44 returned 0 after 0 usecs
calling init_script_binfmt+0x0/0x10 @ 1
initcall init_script_binfmt+0x0/0x10 returned 0 after 0 usecs
calling init_elf_binfmt+0x0/0x10 @ 1
initcall init_elf_binfmt+0x0/0x10 returned 0 after 0 usecs
calling debugfs_init+0x0/0x60 @ 1
initcall debugfs_init+0x0/0x60 returned 0 after 0 usecs
calling random32_init+0x0/0xdc @ 1
initcall random32_init+0x0/0xdc returned 0 after 0 usecs
calling regulator_init+0x0/0x6c @ 1
#### hwftest platform_device_add(): reg-dummy
Registering platform device 'reg-dummy'. Parent at platform
~~~~ hwftest bus: 'platform': add device reg-dummy
==== hwftest bus: 'platform': add device reg-dummy ok!

Registering platform device ==== add OK

print_constraints: dummy:
initcall regulator_init+0x0/0x6c returned 0 after 19531 usecs
calling cpufreq_core_init+0x0/0xc8 @ 1
initcall cpufreq_core_init+0x0/0xc8 returned 0 after 0 usecs
calling sock_init+0x0/0x8c @ 1
initcall sock_init+0x0/0x8c returned 0 after 0 usecs
calling netlink_proto_init+0x0/0x1c4 @ 1
NET: Registered protocol family 16
initcall netlink_proto_init+0x0/0x1c4 returned 0 after 0 usecs
calling post_cpu_init+0x0/0x214 @ 1
initcall post_cpu_init+0x0/0x214 returned 0 after 0 usecs
calling regulators_init+0x0/0x9c @ 1
#### hwftest platform_device_add(): anatop_reg
Registering platform device 'anatop_reg.0'. Parent at platform
~~~~ hwftest bus: 'platform': add device anatop_reg.0
==== hwftest bus: 'platform': add device anatop_reg.0 ok!

Registering platform device ==== add OK

#### hwftest platform_device_add(): anatop_reg
Registering platform device 'anatop_reg.1'. Parent at platform
~~~~ hwftest bus: 'platform': add device anatop_reg.1
==== hwftest bus: 'platform': add device anatop_reg.1 ok!

Registering platform device ==== add OK

#### hwftest platform_device_add(): anatop_reg
Registering platform device 'anatop_reg.2'. Parent at platform
~~~~ hwftest bus: 'platform': add device anatop_reg.2
==== hwftest bus: 'platform': add device anatop_reg.2 ok!

Registering platform device ==== add OK

#### hwftest platform_device_add(): anatop_reg
Registering platform device 'anatop_reg.3'. Parent at platform
~~~~ hwftest bus: 'platform': add device anatop_reg.3
==== hwftest bus: 'platform': add device anatop_reg.3 ok!

Registering platform device ==== add OK

#### hwftest platform_device_add(): anatop_reg
Registering platform device 'anatop_reg.4'. Parent at platform
~~~~ hwftest bus: 'platform': add device anatop_reg.4
==== hwftest bus: 'platform': add device anatop_reg.4 ok!

Registering platform device ==== add OK

#### hwftest platform_device_add(): anatop_reg
Registering platform device 'anatop_reg.5'. Parent at platform
~~~~ hwftest bus: 'platform': add device anatop_reg.5
==== hwftest bus: 'platform': add device anatop_reg.5 ok!

Registering platform device ==== add OK

initcall regulators_init+0x0/0x9c returned 0 after 146484 usecs
calling mxc_audmux_v2_init+0x0/0xb8 @ 1
initcall mxc_audmux_v2_init+0x0/0xb8 returned 0 after 0 usecs
calling bdi_class_init+0x0/0x58 @ 1
initcall bdi_class_init+0x0/0x58 returned 0 after 0 usecs
calling kobject_uevent_init+0x0/0x20 @ 1
initcall kobject_uevent_init+0x0/0x20 returned 0 after 0 usecs
calling gpiolib_sysfs_init+0x0/0x98 @ 1
initcall gpiolib_sysfs_init+0x0/0x98 returned 0 after 9765 usecs
calling backlight_class_init+0x0/0x70 @ 1
initcall backlight_class_init+0x0/0x70 returned 0 after 0 usecs
calling amba_init+0x0/0xc @ 1
initcall amba_init+0x0/0xc returned 0 after 0 usecs
calling anatop_regulator_init+0x0/0xc @ 1
~~~~ hwftest driver_register: anatop_reg
print_constraints: vddpu: 725 <--> 1300 mV at 700 mV fast normal
print_constraints: vddcore: 725 <--> 1300 mV at 1150 mV fast normal
print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal
print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal
print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal
print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal
initcall anatop_regulator_init+0x0/0xc returned 0 after 48828 usecs
calling tty_class_init+0x0/0x44 @ 1
initcall tty_class_init+0x0/0x44 returned 0 after 0 usecs
calling vtconsole_class_init+0x0/0xec @ 1
initcall vtconsole_class_init+0x0/0xec returned 0 after 0 usecs
calling wakeup_sources_debugfs_init+0x0/0x44 @ 1
initcall wakeup_sources_debugfs_init+0x0/0x44 returned 0 after 0 usecs
calling spi_init+0x0/0x90 @ 1
initcall spi_init+0x0/0x90 returned 0 after 0 usecs
calling i2c_init+0x0/0x70 @ 1
~~~~ hwftest driver_register: dummy
initcall i2c_init+0x0/0x70 returned 0 after 0 usecs
calling customize_machine+0x0/0x28 @ 1

==== file: arch/arm/mach-mx6/board-mx6q_sabreauto.c mx6_board_init()[1525]
==== test0
==== test1
==== test2
==== test3
#### hwftest platform_device_add(): imx-uart
#### hwftest platform_device_add() r->name: imx-uart.1
#### hwftest platform_device_add() r->name: imx-uart.1
Registering platform device 'imx-uart.1'. Parent at platform
~~~~ hwftest bus: 'platform': add device imx-uart.1
==== hwftest bus: 'platform': add device imx-uart.1 ok!

Registering platform device ==== add OK

==== test4
==== test5
==== test6
==== test7
==== test8
#### hwftest platform_device_add(): mxs-dma-apbh
#### hwftest platform_device_add() r->name: mxs-dma-apbh
Registering platform device 'mxs-dma-apbh'. Parent at platform
~~~~ hwftest bus: 'platform': add device mxs-dma-apbh
==== hwftest bus: 'platform': add device mxs-dma-apbh ok!

Registering platform device ==== add OK

==== test9
#### hwftest platform_device_add(): imx6q-gpmi-nand
#### hwftest platform_device_add() r->name: GPMI NAND GPMI Registers
#### hwftest platform_device_add() r->name: GPMI NAND GPMI Interrupt
#### hwftest platform_device_add() r->name: GPMI NAND BCH Registers
#### hwftest platform_device_add() r->name: GPMI NAND BCH Interrupt
#### hwftest platform_device_add() r->name: GPMI NAND DMA Channels
#### hwftest platform_device_add() r->name: GPMI NAND DMA Interrupt
Registering platform device 'imx6q-gpmi-nand.0'. Parent at platform
~~~~ hwftest bus: 'platform': add device imx6q-gpmi-nand.0
==== hwftest bus: 'platform': add device imx6q-gpmi-nand.0 ok!

Registering platform device ==== add OK

#### hwftest platform_device_add(): imx_busfreq
Registering platform device 'imx_busfreq.0'. Parent at platform
~~~~ hwftest bus: 'platform': add device imx_busfreq.0
==== hwftest bus: 'platform': add device imx_busfreq.0 ok!

Registering platform device ==== add OK

==== test10

---- exit file: arch/arm/mach-mx6/board-mx6q_sabreauto.c mx6_board_init()[1862]
initcall customize_machine+0x0/0x28 returned 0 after 185546 usecs
calling arch_hw_breakpoint_init+0x0/0x204 @ 1
hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
hw-breakpoint: maximum watchpoint size is 4 bytes.
initcall arch_hw_breakpoint_init+0x0/0x204 returned 0 after 9765 usecs
calling armpmu_reset+0x0/0x2c @ 1
initcall armpmu_reset+0x0/0x2c returned 0 after 0 usecs
calling exceptions_init+0x0/0x98 @ 1
initcall exceptions_init+0x0/0x98 returned 0 after 0 usecs
calling mxc_init_l2x0+0x0/0x134 @ 1
L310 cache controller enabled
l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x02070000, Cache size: 1048576 B
initcall mxc_init_l2x0+0x0/0x134 returned 0 after 9765 usecs
calling imxXX_add_imx_dma+0x0/0xa8 @ 1
#### hwftest platform_device_add(): imx-sdma
#### hwftest platform_device_add() r->name: imx-sdma
#### hwftest platform_device_add() r->name: imx-sdma
Registering platform device 'imx-sdma'. Parent at platform
~~~~ hwftest bus: 'platform': add device imx-sdma
==== hwftest bus: 'platform': add device imx-sdma ok!

Registering platform device ==== add OK

initcall imxXX_add_imx_dma+0x0/0xa8 returned 0 after 29296 usecs
calling dma_bus_init+0x0/0x40 @ 1
initcall dma_bus_init+0x0/0x40 returned 0 after 0 usecs
calling dma_channel_table_init+0x0/0x114 @ 1
initcall dma_channel_table_init+0x0/0x114 returned 0 after 0 usecs
calling topology_init+0x0/0x70 @ 1
initcall topology_init+0x0/0x70 returned 0 after 0 usecs
calling etm_init+0x0/0x98 @ 1
~~~~ hwftest bus: 'amba': add device etb
==== hwftest bus: 'amba': add device etb ok!

~~~~ hwftest bus: 'amba': add device etm.0
==== hwftest bus: 'amba': add device etm.0 ok!

~~~~ hwftest bus: 'amba': add device etm.1
==== hwftest bus: 'amba': add device etm.1 ok!

~~~~ hwftest bus: 'amba': add device etm.2
==== hwftest bus: 'amba': add device etm.2 ok!

~~~~ hwftest bus: 'amba': add device etm.3
==== hwftest bus: 'amba': add device etm.3 ok!

initcall etm_init+0x0/0x98 returned 0 after 39062 usecs
calling isp1504xc_init+0x0/0x24 @ 1
initcall isp1504xc_init+0x0/0x24 returned 0 after 0 usecs
calling utmixc_init+0x0/0x18 @ 1
initcall utmixc_init+0x0/0x18 returned 0 after 0 usecs
calling serialxc_init+0x0/0x18 @ 1
initcall serialxc_init+0x0/0x18 returned 0 after 0 usecs
calling hsic_xcvr_init+0x0/0x18 @ 1
initcall hsic_xcvr_init+0x0/0x18 returned 0 after 0 usecs
calling param_sysfs_init+0x0/0x1b0 @ 1
initcall param_sysfs_init+0x0/0x1b0 returned 0 after 19531 usecs
calling pm_sysrq_init+0x0/0x1c @ 1
initcall pm_sysrq_init+0x0/0x1c returned 0 after 0 usecs
calling default_bdi_init+0x0/0xb0 @ 1
initcall default_bdi_init+0x0/0xb0 returned 0 after 0 usecs
calling init_bio+0x0/0x114 @ 1
bio: create slab at 0
initcall init_bio+0x0/0x114 returned 0 after 0 usecs
calling fsnotify_notification_init+0x0/0x9c @ 1
initcall fsnotify_notification_init+0x0/0x9c returned 0 after 0 usecs
calling cryptomgr_init+0x0/0xc @ 1
initcall cryptomgr_init+0x0/0xc returned 0 after 0 usecs
calling blk_settings_init+0x0/0x38 @ 1
initcall blk_settings_init+0x0/0x38 returned 0 after 0 usecs
calling blk_ioc_init+0x0/0x40 @ 1
initcall blk_ioc_init+0x0/0x40 returned 0 after 0 usecs
calling blk_softirq_init+0x0/0x84 @ 1
initcall blk_softirq_init+0x0/0x84 returned 0 after 0 usecs
calling blk_iopoll_setup+0x0/0x84 @ 1
initcall blk_iopoll_setup+0x0/0x84 returned 0 after 0 usecs
calling genhd_device_init+0x0/0x7c @ 1
initcall genhd_device_init+0x0/0x7c returned 0 after 0 usecs
calling gpiolib_debugfs_init+0x0/0x38 @ 1
initcall gpiolib_debugfs_init+0x0/0x38 returned 0 after 0 usecs
calling pca953x_init+0x0/0x10 @ 1
~~~~ hwftest driver_register: pca953x
initcall pca953x_init+0x0/0x10 returned 0 after 0 usecs
calling fbmem_init+0x0/0xb0 @ 1
initcall fbmem_init+0x0/0xb0 returned 0 after 0 usecs
calling pxp_init+0x0/0xc @ 1
~~~~ hwftest driver_register: imx-pxp
initcall pxp_init+0x0/0xc returned 0 after 0 usecs
calling mxs_dma_module_init+0x0/0x14 @ 1
~~~~ hwftest driver_register: mxs-dma
mxs-dma mxs-dma-apbh: initialized
initcall mxs_dma_module_init+0x0/0x14 returned 0 after 9765 usecs
calling regulator_fixed_voltage_init+0x0/0xc @ 1
~~~~ hwftest driver_register: reg-fixed-voltage
initcall regulator_fixed_voltage_init+0x0/0xc returned 0 after 9765 usecs
calling pfuze100_regulator_init+0x0/0xc @ 1
~~~~ hwftest driver_register: pfuze100-regulator
initcall pfuze100_regulator_init+0x0/0xc returned 0 after 0 usecs
calling max17135_regulator_init+0x0/0xc @ 1
~~~~ hwftest driver_register: max17135-reg
initcall max17135_regulator_init+0x0/0xc returned 0 after 9765 usecs
calling misc_init+0x0/0xc0 @ 1
initcall misc_init+0x0/0xc0 returned 0 after 0 usecs
calling cn_init+0x0/0xac @ 1
initcall cn_init+0x0/0xac returned 0 after 0 usecs
calling pfuze_init+0x0/0x10 @ 1
~~~~ hwftest driver_register: mc_pfuze
initcall pfuze_init+0x0/0x10 returned 0 after 0 usecs
calling mxc_hdmi_core_init+0x0/0x14 @ 1
~~~~ hwftest driver_register: mxc_hdmi_core
initcall mxc_hdmi_core_init+0x0/0x14 returned -19 after 9765 usecs
calling init_scsi+0x0/0x88 @ 1
SCSI subsystem initialized
initcall init_scsi+0x0/0x88 returned 0 after 9765 usecs
calling ata_init+0x0/0x368 @ 1
initcall ata_init+0x0/0x368 returned 0 after 0 usecs
calling spi_imx_init+0x0/0xc @ 1
~~~~ hwftest driver_register: spi_imx
initcall spi_imx_init+0x0/0xc returned 0 after 9765 usecs
calling phy_init+0x0/0x3c @ 1
~~~~ hwftest driver_register: Generic PHY
initcall phy_init+0x0/0x3c returned 0 after 0 usecs
calling usb_init+0x0/0x184 @ 1
~~~~ hwftest drivers/usb/core/usb.c usb_init
~~~~ hwftest driver_register: usbfs
usbcore: registered new interface driver usbfs
~~~~ hwftest driver_register: hub
usbcore: registered new interface driver hub
~~~~ hwftest driver_register: usb
usbcore: registered new device driver usb
initcall usb_init+0x0/0x184 returned 0 after 19531 usecs
calling fsl_usb_otg_init+0x0/0x28 @ 1
Freescale USB OTG Driver loaded, $Revision: 1.55 $
~~~~ hwftest driver_register: fsl-usb2-otg
initcall fsl_usb_otg_init+0x0/0x28 returned 0 after 9765 usecs
calling serio_init+0x0/0x30 @ 1
initcall serio_init+0x0/0x30 returned 0 after 0 usecs
calling input_init+0x0/0x11c @ 1
initcall input_init+0x0/0x11c returned 0 after 0 usecs
calling rtc_init+0x0/0x74 @ 1
initcall rtc_init+0x0/0x74 returned 0 after 0 usecs
calling i2c_adap_imx_init+0x0/0x14 @ 1
~~~~ hwftest driver_register: imx-i2c
initcall i2c_adap_imx_init+0x0/0x14 returned -19 after 9765 usecs
calling power_supply_class_init+0x0/0x50 @ 1
initcall power_supply_class_init+0x0/0x50 returned 0 after 0 usecs
calling hwmon_init+0x0/0x48 @ 1
initcall hwmon_init+0x0/0x48 returned 0 after 0 usecs
calling mmc_init+0x0/0x80 @ 1
initcall mmc_init+0x0/0x80 returned 0 after 0 usecs
calling ipu_gen_init+0x0/0x18 @ 1
~~~~ hwftest driver_register: imx-ipuv3
initcall ipu_gen_init+0x0/0x18 returned 0 after 0 usecs
calling mipi_csi2_init+0x0/0x40 @ 1
~~~~ hwftest driver_register: mxc_mipi_csi2
MIPI CSI2 driver module loaded
initcall mipi_csi2_init+0x0/0x40 returned 0 after 9765 usecs
calling leds_init+0x0/0x5c @ 1
initcall leds_init+0x0/0x5c returned 0 after 0 usecs
calling init_soundcore+0x0/0x44 @ 1
initcall init_soundcore+0x0/0x44 returned 0 after 0 usecs
calling alsa_sound_init+0x0/0xac @ 1
Advanced Linux Sound Architecture Driver Version 1.0.24.
initcall alsa_sound_init+0x0/0xac returned 0 after 0 usecs
calling ac97_bus_init+0x0/0xc @ 1
initcall ac97_bus_init+0x0/0xc returned 0 after 0 usecs
calling proto_init+0x0/0xc @ 1
initcall proto_init+0x0/0xc returned 0 after 0 usecs
calling net_dev_init+0x0/0x1ec @ 1
initcall net_dev_init+0x0/0x1ec returned 0 after 9765 usecs
calling neigh_init+0x0/0x84 @ 1
initcall neigh_init+0x0/0x84 returned 0 after 0 usecs
calling genl_init+0x0/0x8c @ 1
initcall genl_init+0x0/0x8c returned 0 after 0 usecs
calling bt_init+0x0/0x88 @ 1
Bluetooth: Core ver 2.16
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP socket layer initialized
Bluetooth: SCO socket layer initialized
initcall bt_init+0x0/0x88 returned 0 after 19531 usecs
calling cfg80211_init+0x0/0xc8 @ 1
#### hwftest platform_device_add(): regulatory
Registering platform device 'regulatory.0'. Parent at platform
~~~~ hwftest bus: 'platform': add device regulatory.0
==== hwftest bus: 'platform': add device regulatory.0 ok!

Registering platform device ==== add OK

cfg80211: Calling CRDA to update world regulatory domain
initcall cfg80211_init+0x0/0xc8 returned 0 after 29296 usecs
calling wireless_nlevent_init+0x0/0xc @ 1
initcall wireless_nlevent_init+0x0/0xc returned 0 after 0 usecs
calling rfkill_init+0x0/0x88 @ 1
initcall rfkill_init+0x0/0x88 returned 0 after 0 usecs
calling sysctl_init+0x0/0x4c @ 1
initcall sysctl_init+0x0/0x4c returned 0 after 0 usecs
calling max17135_init+0x0/0x10 @ 1
~~~~ hwftest driver_register: max17135
i2c-core: driver [max17135] using legacy suspend method
i2c-core: driver [max17135] using legacy resume method
initcall max17135_init+0x0/0x10 returned 0 after 19531 usecs
calling proc_cpu_init+0x0/0x24 @ 1
initcall proc_cpu_init+0x0/0x24 returned 0 after 0 usecs
calling dma_debug_do_init+0x0/0x8 @ 1
initcall dma_debug_do_init+0x0/0x8 returned 0 after 0 usecs
calling alignment_init+0x0/0xec @ 1
initcall alignment_init+0x0/0xec returned 0 after 0 usecs
calling clocksource_done_booting+0x0/0x50 @ 1
Switching to clocksource mxc_timer1
initcall clocksource_done_booting+0x0/0x50 returned 0 after 9771 usecs
calling init_pipe_fs+0x0/0x50 @ 1
initcall init_pipe_fs+0x0/0x50 returned 0 after 80 usecs
calling eventpoll_init+0x0/0xcc @ 1
initcall eventpoll_init+0x0/0xcc returned 0 after 40 usecs
calling anon_inode_init+0x0/0x134 @ 1
initcall anon_inode_init+0x0/0x134 returned 0 after 43 usecs
calling blk_scsi_ioctl_init+0x0/0xe0 @ 1
initcall blk_scsi_ioctl_init+0x0/0xe0 returned 0 after 1 usecs
calling chr_dev_init+0x0/0xdc @ 1
initcall chr_dev_init+0x0/0xdc returned 0 after 12555 usecs
calling firmware_class_init+0x0/0x14 @ 1
initcall firmware_class_init+0x0/0x14 returned 0 after 130 usecs
calling thermal_init+0x0/0x70 @ 1
initcall thermal_init+0x0/0x70 returned 0 after 124 usecs
calling cpufreq_gov_performance_init+0x0/0xc @ 1
initcall cpufreq_gov_performance_init+0x0/0xc returned 0 after 2 usecs
calling sysctl_core_init+0x0/0x38 @ 1
initcall sysctl_core_init+0x0/0x38 returned 0 after 34 usecs
calling inet_init+0x0/0x26c @ 1
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
UDP hash table entries: 512 (order: 2, 16384 bytes)
UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
initcall inet_init+0x0/0x26c returned 0 after 40914 usecs
calling af_unix_init+0x0/0x54 @ 1
NET: Registered protocol family 1
initcall af_unix_init+0x0/0x54 returned 0 after 3027 usecs
calling init_sunrpc+0x0/0x70 @ 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
initcall init_sunrpc+0x0/0x70 returned 0 after 16557 usecs
calling default_rootfs+0x0/0x68 @ 1
initcall default_rootfs+0x0/0x68 returned 0 after 52 usecs
calling timer_init_syscore_ops+0x0/0x18 @ 1
initcall timer_init_syscore_ops+0x0/0x18 returned 0 after 3 usecs
calling etm_init+0x0/0x88 @ 1
~~~~ hwftest driver_register: etb
~~~~ hwftest driver_register: etm
initcall etm_init+0x0/0x88 returned 0 after 6754 usecs
calling register_pmu_driver+0x0/0xc @ 1
~~~~ hwftest driver_register: arm-pmu
initcall register_pmu_driver+0x0/0xc returned 0 after 3477 usecs
calling pm_init+0x0/0x298 @ 1
Static Power Management for Freescale i.MX6
wait mode is enabled for i.MX6
~~~~ hwftest driver_register: imx_pm
cpaddr = c0880000 suspend_iram_base=c0828000
PM driver module loaded
initcall pm_init+0x0/0x298 returned 0 after 16158 usecs
calling mx6_usb_h1_init+0x0/0x14c @ 1
#### hwftest platform_device_add(): usb-wakeup
#### hwftest platform_device_add() r->name: usb-wakeup.1
#### hwftest platform_device_add() r->name: usb-wakeup.1
Registering platform device 'usb-wakeup.1'. Parent at platform
~~~~ hwftest bus: 'platform': add device usb-wakeup.1
==== hwftest bus: 'platform': add device usb-wakeup.1 ok!

Registering platform device ==== add OK

#### hwftest platform_device_add(): fsl-ehci
#### hwftest platform_device_add() r->name: fsl-ehci.1
#### hwftest platform_device_add() r->name: fsl-ehci.1
Registering platform device 'fsl-ehci.1'. Parent at platform
~~~~ hwftest bus: 'platform': add device fsl-ehci.1
==== hwftest bus: 'platform': add device fsl-ehci.1 ok!

Registering platform device ==== add OK

initcall mx6_usb_h1_init+0x0/0x14c returned 0 after 67695 usecs
calling mxc_cpufreq_driver_init+0x0/0x40 @ 1
cpu regulator mode:ldo_enable
i.MXC CPU frequency driver
initcall mxc_cpufreq_driver_init+0x0/0x40 returned 0 after 5464 usecs
calling proc_execdomains_init+0x0/0x38 @ 1
initcall proc_execdomains_init+0x0/0x38 returned 0 after 9 usecs
calling ioresources_init+0x0/0x58 @ 1
initcall ioresources_init+0x0/0x58 returned 0 after 8 usecs
calling uid_cache_init+0x0/0x9c @ 1
initcall uid_cache_init+0x0/0x9c returned 0 after 14 usecs
calling init_posix_timers+0x0/0x1d8 @ 1
initcall init_posix_timers+0x0/0x1d8 returned 0 after 32 usecs
calling init_posix_cpu_timers+0x0/0xe4 @ 1
initcall init_posix_cpu_timers+0x0/0xe4 returned 0 after 1 usecs
calling nsproxy_cache_init+0x0/0x40 @ 1
initcall nsproxy_cache_init+0x0/0x40 returned 0 after 5 usecs
calling timekeeping_init_ops+0x0/0x18 @ 1
initcall timekeeping_init_ops+0x0/0x18 returned 0 after 2 usecs
calling init_clocksource_sysfs+0x0/0x50 @ 1
initcall init_clocksource_sysfs+0x0/0x50 returned 0 after 185 usecs
calling init_timer_list_procfs+0x0/0x40 @ 1
initcall init_timer_list_procfs+0x0/0x40 returned 0 after 9 usecs
calling alarmtimer_init+0x0/0x144 @ 1
~~~~ hwftest driver_register: alarmtimer
#### hwftest platform_device_add(): alarmtimer
Registering platform device 'alarmtimer'. Parent at platform
~~~~ hwftest bus: 'platform': add device alarmtimer
==== hwftest bus: 'platform': add device alarmtimer ok!

Registering platform device ==== add OK

initcall alarmtimer_init+0x0/0x144 returned 0 after 26920 usecs
calling futex_init+0x0/0x78 @ 1
initcall futex_init+0x0/0x78 returned 0 after 12 usecs
calling proc_modules_init+0x0/0x38 @ 1
initcall proc_modules_init+0x0/0x38 returned 0 after 6 usecs
calling kallsyms_init+0x0/0x38 @ 1
initcall kallsyms_init+0x0/0x38 returned 0 after 4 usecs
calling ikconfig_init+0x0/0x4c @ 1
initcall ikconfig_init+0x0/0x4c returned 0 after 4 usecs
calling irq_pm_init_ops+0x0/0x18 @ 1
initcall irq_pm_init_ops+0x0/0x18 returned 0 after 1 usecs
calling utsname_sysctl_init+0x0/0x18 @ 1
initcall utsname_sysctl_init+0x0/0x18 returned 0 after 40 usecs
calling perf_event_sysfs_init+0x0/0xac @ 1
~~~~ hwftest bus: 'event_source': add device cpu
==== hwftest bus: 'event_source': add device cpu ok!

~~~~ hwftest bus: 'event_source': add device breakpoint
==== hwftest bus: 'event_source': add device breakpoint ok!

~~~~ hwftest bus: 'event_source': add device software
==== hwftest bus: 'event_source': add device software ok!

initcall perf_event_sysfs_init+0x0/0xac returned 0 after 29951 usecs
calling init_per_zone_wmark_min+0x0/0x90 @ 1
initcall init_per_zone_wmark_min+0x0/0x90 returned 0 after 11833 usecs
calling kswapd_init+0x0/0x24 @ 1
initcall kswapd_init+0x0/0x24 returned 0 after 134 usecs
calling extfrag_debug_init+0x0/0x94 @ 1
initcall extfrag_debug_init+0x0/0x94 returned 0 after 21 usecs
calling setup_vmstat+0x0/0xe4 @ 1
initcall setup_vmstat+0x0/0xe4 returned 0 after 27 usecs
calling mm_sysfs_init+0x0/0x3c @ 1
initcall mm_sysfs_init+0x0/0x3c returned 0 after 12 usecs
calling proc_vmalloc_init+0x0/0x38 @ 1
initcall proc_vmalloc_init+0x0/0x38 returned 0 after 4 usecs
calling memblock_init_debugfs+0x0/0x78 @ 1
initcall memblock_init_debugfs+0x0/0x78 returned 0 after 13 usecs
calling init_emergency_pool+0x0/0x74 @ 1
initcall init_emergency_pool+0x0/0x74 returned 0 after 3 usecs
calling procswaps_init+0x0/0x38 @ 1
initcall procswaps_init+0x0/0x38 returned 0 after 5 usecs
calling ksm_init+0x0/0x158 @ 1
initcall ksm_init+0x0/0x158 returned 0 after 88 usecs
calling slab_proc_init+0x0/0x38 @ 1
initcall slab_proc_init+0x0/0x38 returned 0 after 5 usecs
calling slab_sysfs_init+0x0/0x110 @ 1
initcall slab_sysfs_init+0x0/0x110 returned 0 after 9127 usecs
calling fcntl_init+0x0/0x40 @ 1
initcall fcntl_init+0x0/0x40 returned 0 after 24 usecs
calling proc_filesystems_init+0x0/0x38 @ 1
initcall proc_filesystems_init+0x0/0x38 returned 0 after 9 usecs
calling fsnotify_mark_init+0x0/0x40 @ 1
initcall fsnotify_mark_init+0x0/0x40 returned 0 after 61 usecs
calling dnotify_init+0x0/0x84 @ 1
initcall dnotify_init+0x0/0x84 returned 0 after 225 usecs
calling inotify_user_setup+0x0/0x78 @ 1
initcall inotify_user_setup+0x0/0x78 returned 0 after 28 usecs
calling aio_setup+0x0/0x98 @ 1
initcall aio_setup+0x0/0x98 returned 0 after 60 usecs
calling proc_locks_init+0x0/0x38 @ 1
initcall proc_locks_init+0x0/0x38 returned 0 after 6 usecs
calling init_mbcache+0x0/0x18 @ 1
initcall init_mbcache+0x0/0x18 returned 0 after 1 usecs
calling proc_cmdline_init+0x0/0x38 @ 1
initcall proc_cmdline_init+0x0/0x38 returned 0 after 6 usecs
calling proc_consoles_init+0x0/0x38 @ 1
initcall proc_consoles_init+0x0/0x38 returned 0 after 4 usecs
calling proc_cpuinfo_init+0x0/0x38 @ 1
initcall proc_cpuinfo_init+0x0/0x38 returned 0 after 4 usecs
calling proc_devices_init+0x0/0x38 @ 1
initcall proc_devices_init+0x0/0x38 returned 0 after 4 usecs
calling proc_interrupts_init+0x0/0x38 @ 1
initcall proc_interrupts_init+0x0/0x38 returned 0 after 4 usecs
calling proc_loadavg_init+0x0/0x38 @ 1
initcall proc_loadavg_init+0x0/0x38 returned 0 after 5 usecs
calling proc_meminfo_init+0x0/0x38 @ 1
initcall proc_meminfo_init+0x0/0x38 returned 0 after 4 usecs
calling proc_stat_init+0x0/0x38 @ 1
initcall proc_stat_init+0x0/0x38 returned 0 after 4 usecs
calling proc_uptime_init+0x0/0x38 @ 1
initcall proc_uptime_init+0x0/0x38 returned 0 after 4 usecs
calling proc_version_init+0x0/0x38 @ 1
initcall proc_version_init+0x0/0x38 returned 0 after 5 usecs
calling proc_softirqs_init+0x0/0x38 @ 1
initcall proc_softirqs_init+0x0/0x38 returned 0 after 4 usecs
calling proc_kmsg_init+0x0/0x38 @ 1
initcall proc_kmsg_init+0x0/0x38 returned 0 after 4 usecs
calling proc_page_init+0x0/0x58 @ 1
initcall proc_page_init+0x0/0x58 returned 0 after 7 usecs
calling init_devpts_fs+0x0/0x50 @ 1
initcall init_devpts_fs+0x0/0x50 returned 0 after 48 usecs
calling init_ext3_fs+0x0/0x88 @ 1
initcall init_ext3_fs+0x0/0x88 returned 0 after 379 usecs
calling init_ext2_fs+0x0/0x78 @ 1
initcall init_ext2_fs+0x0/0x78 returned 0 after 182 usecs
calling ext4_init_fs+0x0/0x204 @ 1
initcall ext4_init_fs+0x0/0x204 returned 0 after 1196 usecs
calling journal_init+0x0/0xc0 @ 1
initcall journal_init+0x0/0xc0 returned 0 after 424 usecs
calling journal_init+0x0/0x120 @ 1
initcall journal_init+0x0/0x120 returned 0 after 263 usecs
calling init_cramfs_fs+0x0/0x3c @ 1
initcall init_cramfs_fs+0x0/0x3c returned 0 after 22 usecs
calling init_ramfs_fs+0x0/0xc @ 1
initcall init_ramfs_fs+0x0/0xc returned 0 after 2 usecs
calling init_fat_fs+0x0/0x60 @ 1
initcall init_fat_fs+0x0/0x60 returned 0 after 355 usecs
calling init_vfat_fs+0x0/0xc @ 1
initcall init_vfat_fs+0x0/0xc returned 0 after 3 usecs
calling init_msdos_fs+0x0/0xc @ 1
initcall init_msdos_fs+0x0/0xc returned 0 after 3 usecs
calling init_nfs_fs+0x0/0x144 @ 1
initcall init_nfs_fs+0x0/0x144 returned 0 after 884 usecs
calling init_nlm+0x0/0x30 @ 1
initcall init_nlm+0x0/0x30 returned 0 after 35 usecs
calling init_nls_cp437+0x0/0xc @ 1
initcall init_nls_cp437+0x0/0xc returned 0 after 2 usecs
calling init_nls_iso8859_1+0x0/0xc @ 1
initcall init_nls_iso8859_1+0x0/0xc returned 0 after 1 usecs
calling init_jffs2_fs+0x0/0xd8 @ 1
JFFS2 version 2.2. (NAND) ?? 2001-2006 Red Hat, Inc.
initcall init_jffs2_fs+0x0/0xd8 returned 0 after 5185 usecs
calling ipc_init+0x0/0x24 @ 1
msgmni has been set to 1751
initcall ipc_init+0x0/0x24 returned 0 after 2500 usecs
calling ipc_sysctl_init+0x0/0x18 @ 1
initcall ipc_sysctl_init+0x0/0x18 returned 0 after 55 usecs
calling crypto_wq_init+0x0/0x4c @ 1
initcall crypto_wq_init+0x0/0x4c returned 0 after 75 usecs
calling crypto_algapi_init+0x0/0x10 @ 1
initcall crypto_algapi_init+0x0/0x10 returned 0 after 9 usecs
calling skcipher_module_init+0x0/0x48 @ 1
initcall skcipher_module_init+0x0/0x48 returned 0 after 0 usecs
calling chainiv_module_init+0x0/0xc @ 1
initcall chainiv_module_init+0x0/0xc returned 0 after 4 usecs
calling eseqiv_module_init+0x0/0xc @ 1
initcall eseqiv_module_init+0x0/0xc returned 0 after 2 usecs
calling seqiv_module_init+0x0/0xc @ 1
initcall seqiv_module_init+0x0/0xc returned 0 after 2 usecs
calling crypto_ecb_module_init+0x0/0xc @ 1
initcall crypto_ecb_module_init+0x0/0xc returned 0 after 2 usecs
calling crypto_cbc_module_init+0x0/0xc @ 1
initcall crypto_cbc_module_init+0x0/0xc returned 0 after 1 usecs
calling crypto_pcbc_module_init+0x0/0xc @ 1
initcall crypto_pcbc_module_init+0x0/0xc returned 0 after 2 usecs
calling crypto_cts_module_init+0x0/0xc @ 1
initcall crypto_cts_module_init+0x0/0xc returned 0 after 2 usecs
calling crypto_module_init+0x0/0xc @ 1
initcall crypto_module_init+0x0/0xc returned 0 after 2 usecs
calling crypto_module_init+0x0/0xc @ 1
initcall crypto_module_init+0x0/0xc returned 0 after 2 usecs
calling crypto_ctr_module_init+0x0/0x3c @ 1
initcall crypto_ctr_module_init+0x0/0x3c returned 0 after 2 usecs
calling crypto_gcm_module_init+0x0/0xb8 @ 1
initcall crypto_gcm_module_init+0x0/0xb8 returned 0 after 5 usecs
calling crypto_ccm_module_init+0x0/0x58 @ 1
initcall crypto_ccm_module_init+0x0/0x58 returned 0 after 3 usecs
calling des_generic_mod_init+0x0/0x3c @ 1
initcall des_generic_mod_init+0x0/0x3c returned 0 after 256 usecs
calling aes_init+0x0/0xc @ 1
initcall aes_init+0x0/0xc returned 0 after 146 usecs
calling arc4_init+0x0/0xc @ 1
initcall arc4_init+0x0/0xc returned 0 after 160 usecs
calling deflate_mod_init+0x0/0xc @ 1
initcall deflate_mod_init+0x0/0xc returned 0 after 466 usecs
calling michael_mic_init+0x0/0xc @ 1
initcall michael_mic_init+0x0/0xc returned 0 after 120 usecs
calling crypto_authenc_module_init+0x0/0xc @ 1
initcall crypto_authenc_module_init+0x0/0xc returned 0 after 2 usecs
calling crypto_authenc_esn_module_init+0x0/0xc @ 1
initcall crypto_authenc_esn_module_init+0x0/0xc returned 0 after 2 usecs
calling lzo_mod_init+0x0/0xc @ 1
initcall lzo_mod_init+0x0/0xc returned 0 after 115 usecs
calling krng_mod_init+0x0/0xc @ 1
alg: No test for stdrng (krng)
initcall krng_mod_init+0x0/0xc returned 0 after 2805 usecs
calling ghash_mod_init+0x0/0xc @ 1
initcall ghash_mod_init+0x0/0xc returned 0 after 110 usecs
calling proc_genhd_init+0x0/0x58 @ 1
initcall proc_genhd_init+0x0/0x58 returned 0 after 14 usecs
calling noop_init+0x0/0x18 @ 1
io scheduler noop registered
initcall noop_init+0x0/0x18 returned 0 after 2576 usecs
calling deadline_init+0x0/0x18 @ 1
io scheduler deadline registered
initcall deadline_init+0x0/0x18 returned 0 after 2916 usecs
calling cfq_init+0x0/0xb8 @ 1
io scheduler cfq registered (default)
initcall cfq_init+0x0/0xb8 returned 0 after 3411 usecs
calling percpu_counter_startup+0x0/0x1c @ 1
initcall percpu_counter_startup+0x0/0x1c returned 0 after 2 usecs
calling fb_console_init+0x0/0x160 @ 1
initcall fb_console_init+0x0/0x160 returned 0 after 164 usecs
calling pwm_backlight_init+0x0/0xc @ 1
~~~~ hwftest driver_register: pwm-backlight
initcall pwm_backlight_init+0x0/0xc returned 0 after 3969 usecs
calling mxc_hdmi_i2c_init+0x0/0x10 @ 1
~~~~ hwftest driver_register: mxc_hdmi_i2c
initcall mxc_hdmi_i2c_init+0x0/0x10 returned 0 after 3854 usecs
calling mxc_hdmi_init+0x0/0xc @ 1
~~~~ hwftest driver_register: mxc_hdmi
initcall mxc_hdmi_init+0x0/0xc returned 0 after 3538 usecs
calling ldb_init+0x0/0xc @ 1
~~~~ hwftest driver_register: mxc_ldb
initcall ldb_init+0x0/0xc returned 0 after 3445 usecs
calling mipi_dsi_init+0x0/0x40 @ 1
~~~~ hwftest driver_register: mxc_mipi_dsi
MIPI DSI driver module loaded
initcall mipi_dsi_init+0x0/0x40 returned 0 after 6507 usecs
calling mxc_lcdif_init+0x0/0xc @ 1
~~~~ hwftest driver_register: mxc_lcdif
initcall mxc_lcdif_init+0x0/0xc returned 0 after 3611 usecs
calling mxcfb_init+0x0/0xc @ 1
~~~~ hwftest driver_register: mxc_sdc_fb
initcall mxcfb_init+0x0/0xc returned 0 after 3705 usecs
calling mxc_dvi_init+0x0/0x10 @ 1
~~~~ hwftest driver_register: mxc_dvi
initcall mxc_dvi_init+0x0/0x10 returned 0 after 3423 usecs
calling pxp_device_init+0x0/0xc @ 1
~~~~ hwftest driver_register: imx-pxp-client
initcall pxp_device_init+0x0/0xc returned 0 after 4028 usecs
calling sdma_module_init+0x0/0x14 @ 1
~~~~ hwftest driver_register: imx-sdma
imx-sdma imx-sdma: loaded firmware 1.1
imx-sdma imx-sdma: initialized
initcall sdma_module_init+0x0/0x14 returned 0 after 14126 usecs
calling pty_init+0x0/0x3f0 @ 1
initcall pty_init+0x0/0x3f0 returned 0 after 121915 usecs
calling sysrq_init+0x0/0xa4 @ 1
initcall sysrq_init+0x0/0xa4 returned 0 after 26 usecs
calling imx_serial_init+0x0/0x48 @ 1
Serial: IMX driver
~~~~ hwftest driver_register: imx-uart
imx-uart.1: ttymxc1 at MMIO 0x21e8000 (irq = 59) is a IMX
console [ttymxc1] enabled, bootconsole disabled
console [ttymxc1] enabled, bootconsole disabled
initcall imx_serial_init+0x0/0x48 returned 0 after 19220 usecs
calling rand_initialize+0x0/0x2c @ 1
initcall rand_initialize+0x0/0x2c returned 0 after 51 usecs
calling fsl_otp_init+0x0/0xc @ 1
~~~~ hwftest driver_register: imx-ocotp
initcall fsl_otp_init+0x0/0xc returned 0 after 3620 usecs
calling apm_init+0x0/0xd8 @ 1
initcall apm_init+0x0/0xd8 returned 0 after 293 usecs
calling mxs_viim_dev_init+0x0/0xc @ 1
~~~~ hwftest driver_register: mxs_viim
initcall mxs_viim_dev_init+0x0/0xc returned 0 after 3529 usecs
calling cn_proc_init+0x0/0x3c @ 1
initcall cn_proc_init+0x0/0x3c returned 0 after 7 usecs
calling topology_sysfs_init+0x0/0x80 @ 1
initcall topology_sysfs_init+0x0/0x80 returned 0 after 62 usecs
calling loop_init+0x0/0x1a0 @ 1
loop: module loaded
initcall loop_init+0x0/0x1a0 returned 0 after 5057 usecs
calling wm8994_i2c_init+0x0/0x34 @ 1
~~~~ hwftest driver_register: wm8994
initcall wm8994_i2c_init+0x0/0x34 returned 0 after 3343 usecs
calling init_sd+0x0/0x120 @ 1
~~~~ hwftest driver_register: sd
initcall init_sd+0x0/0x120 returned 0 after 3215 usecs
calling ahci_init+0x0/0x14 @ 1
~~~~ hwftest driver_register: ahci
initcall ahci_init+0x0/0x14 returned -19 after 3289 usecs
calling init_mtd+0x0/0xd8 @ 1
initcall init_mtd+0x0/0xd8 returned 0 after 641 usecs
calling cmdline_parser_init+0x0/0xc @ 1
initcall cmdline_parser_init+0x0/0xc returned 0 after 1 usecs
calling init_mtdchar+0x0/0xe0 @ 1
initcall init_mtdchar+0x0/0xe0 returned 0 after 60 usecs
calling init_mtdblock+0x0/0x2c @ 1
initcall init_mtdblock+0x0/0x2c returned 0 after 3 usecs
calling cfi_probe_init+0x0/0x18 @ 1
initcall cfi_probe_init+0x0/0x18 returned 0 after 2 usecs
calling physmap_init+0x0/0xc @ 1
~~~~ hwftest driver_register: physmap-flash
initcall physmap_init+0x0/0xc returned 0 after 3955 usecs
calling m25p80_init+0x0/0xc @ 1
~~~~ hwftest driver_register: m25p80
initcall m25p80_init+0x0/0xc returned 0 after 3352 usecs
calling nand_base_init+0x0/0x20 @ 1
initcall nand_base_init+0x0/0x20 returned 0 after 3 usecs
calling gpmi_nand_init+0x0/0x30 @ 1
~~~~ hwftest driver_register: gpmi-nand
ONFI flash detected
ONFI param page 0 valid
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x68 (Micron MT29F32G08CBACAWP)
gpmi-nand imx6q-gpmi-nand.0: enable asynchronous EDO mode 5
Scanning device for bad blocks
Bad eraseblock 90 at 0x000005a00000
Bad eraseblock 91 at 0x000005b00000
3 cmdlinepart partitions found on MTD device gpmi-nand
Creating 3 MTD partitions on "gpmi-nand":
0x000000000000-0x000001000000 : "boot"
0x000001000000-0x000002000000 : "kernel"
0x000002000000-0x00000a000000 : "rootfs"
GPMI NAND driver registered. (IMX)
initcall gpmi_nand_init+0x0/0x30 returned 0 after 558388 usecs
calling ubi_init+0x0/0x2d0 @ 1
UBI: attaching mtd2 to ubi0
UBI: physical eraseblock size: 1048576 bytes (1024 KiB)
UBI: logical eraseblock size: 1040384 bytes
UBI: smallest flash I/O unit: 4096
UBI: VID header offset: 4096 (aligned 4096)
UBI: data offset: 8192
UBI: max. sequence number: 47
UBI: attached mtd2 to ubi0
UBI: MTD device name: "rootfs"
UBI: MTD device size: 128 MiB
UBI: number of good PEBs: 126
UBI: number of bad PEBs: 2
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 55
UBI: total number of reserved PEBs: 71
UBI: number of PEBs reserved for bad PEB handling: 2
UBI: max/mean erase counter: 1/0
UBI: image sequence number: 1777895053
initcall ubi_init+0x0/0x2d0 returned 0 after 134569 usecs
UBI: background thread "ubi_bgt0d" started, PID 1149
calling ksphy_init+0x0/0x90 @ 1
~~~~ hwftest driver_register: Micrel KS8001 or KS8721
~~~~ hwftest driver_register: Micrel KSZ9021 Gigabit PHY
~~~~ hwftest driver_register: Micrel KS8737
~~~~ hwftest driver_register: Micrel KS8041
~~~~ hwftest driver_register: Micrel KS8051
initcall ksphy_init+0x0/0x90 returned 0 after 21628 usecs
calling vcan_init_module+0x0/0x40 @ 1
vcan: Virtual CAN interface driver
initcall vcan_init_module+0x0/0x40 returned 0 after 3070 usecs
calling can_dev_init+0x0/0x2c @ 1
CAN device driver interface
initcall can_dev_init+0x0/0x2c returned 0 after 2473 usecs
calling flexcan_init+0x0/0x28 @ 1
flexcan netdevice driver
~~~~ hwftest driver_register: flexcan
initcall flexcan_init+0x0/0x28 returned 0 after 5673 usecs
calling net_olddevs_init+0x0/0xc0 @ 1
initcall net_olddevs_init+0x0/0xc0 returned 0 after 11 usecs
calling fec_enet_module_init+0x0/0x20 @ 1
FEC Ethernet Driver
~~~~ hwftest driver_register: fec
initcall fec_enet_module_init+0x0/0x20 returned 0 after 4895 usecs
calling smsc911x_init_module+0x0/0xc @ 1
~~~~ hwftest driver_register: smsc911x
initcall smsc911x_init_module+0x0/0xc returned 0 after 3509 usecs
calling hostap_init+0x0/0x50 @ 1
initcall hostap_init+0x0/0x50 returned 0 after 14 usecs
calling udc_init+0x0/0x30 @ 1
ARC USBOTG Device Controller driver (1 August 2005)
~~~~ hwftest driver_register: fsl-usb2-udc
initcall udc_init+0x0/0x30 returned 0 after 8378 usecs
calling serport_init+0x0/0x30 @ 1
initcall serport_init+0x0/0x30 returned 0 after 4 usecs
calling mousedev_init+0x0/0x88 @ 1
mousedev: PS/2 mouse device common for all mice
initcall mousedev_init+0x0/0x88 returned 0 after 4603 usecs
calling evdev_init+0x0/0xc @ 1
initcall evdev_init+0x0/0xc returned 0 after 2 usecs
calling atkbd_init+0x0/0x18 @ 1
~~~~ hwftest driver_register: atkbd
initcall atkbd_init+0x0/0x18 returned 0 after 3299 usecs
calling gpio_keys_init+0x0/0xc @ 1
~~~~ hwftest driver_register: gpio-keys
initcall gpio_keys_init+0x0/0xc returned 0 after 3603 usecs
calling max11801_ts_init+0x0/0x10 @ 1
~~~~ hwftest driver_register: max11801_ts
initcall max11801_ts_init+0x0/0x10 returned 0 after 3772 usecs
calling egalax_ts_init+0x0/0x10 @ 1
~~~~ hwftest driver_register: egalax_ts
initcall egalax_ts_init+0x0/0x10 returned 0 after 3589 usecs
calling elan_touch_init+0x0/0x10 @ 1
~~~~ hwftest driver_register: elan-touch
initcall elan_touch_init+0x0/0x10 returned 0 after 3685 usecs
calling uinput_init+0x0/0xc @ 1
initcall uinput_init+0x0/0xc returned 0 after 199 usecs
calling isl29023_init+0x0/0x10 @ 1
~~~~ hwftest driver_register: isl29023
i2c-core: driver [isl29023] using legacy suspend method
i2c-core: driver [isl29023] using legacy resume method
initcall isl29023_init+0x0/0x10 returned 0 after 13150 usecs
calling snvs_rtc_init+0x0/0xc @ 1
~~~~ hwftest driver_register: snvs_rtc
initcall snvs_rtc_init+0x0/0xc returned 0 after 3517 usecs
calling i2c_dev_init+0x0/0xd0 @ 1
i2c /dev entries driver
initcall i2c_dev_init+0x0/0xd0 returned 0 after 2242 usecs
calling videodev_init+0x0/0x84 @ 1
Linux video capture interface: v2.00
initcall videodev_init+0x0/0x84 returned 0 after 3328 usecs
calling mxc_vout_init+0x0/0x2c @ 1
~~~~ hwftest driver_register: mxc_v4l2_output
initcall mxc_vout_init+0x0/0x2c returned 0 after 4124 usecs
calling max8903_init+0x0/0xc @ 1
~~~~ hwftest driver_register: max8903-charger
initcall max8903_init+0x0/0xc returned 0 after 4119 usecs
calling sensors_max17135_init+0x0/0xc @ 1
~~~~ hwftest driver_register: max17135_sensor
initcall sensors_max17135_init+0x0/0xc returned 0 after 4112 usecs
calling mag3110_init+0x0/0x10 @ 1
~~~~ hwftest driver_register: mag3110
i2c-core: driver [mag3110] using legacy suspend method
i2c-core: driver [mag3110] using legacy resume method
initcall mag3110_init+0x0/0x10 returned 0 after 12879 usecs
calling mma8451_init+0x0/0x30 @ 1
~~~~ hwftest driver_register: mma8451
initcall mma8451_init+0x0/0x30 returned 0 after 3428 usecs
calling imx2_wdt_init+0x0/0x14 @ 1
~~~~ hwftest driver_register: imx2-wdt
initcall imx2_wdt_init+0x0/0x14 returned -19 after 3611 usecs
calling vhci_init+0x0/0x28 @ 1
Bluetooth: Virtual HCI driver ver 1.3
initcall vhci_init+0x0/0x28 returned 0 after 3525 usecs
calling hci_uart_init+0x0/0xe4 @ 1
Bluetooth: HCI UART driver ver 2.2
Bluetooth: HCIATH3K protocol initialized
initcall hci_uart_init+0x0/0xe4 returned 0 after 6647 usecs
calling btusb_init+0x0/0x34 @ 1
Bluetooth: Generic Bluetooth USB driver ver 0.6
~~~~ hwftest driver_register: btusb
usbcore: registered new interface driver btusb
initcall btusb_init+0x0/0x34 returned 0 after 11556 usecs
calling cpufreq_stats_init+0x0/0xac @ 1
initcall cpufreq_stats_init+0x0/0xac returned 0 after 43 usecs
calling cpufreq_gov_powersave_init+0x0/0xc @ 1
initcall cpufreq_gov_powersave_init+0x0/0xc returned 0 after 2 usecs
calling cpufreq_gov_userspace_init+0x0/0xc @ 1
initcall cpufreq_gov_userspace_init+0x0/0xc returned 0 after 0 usecs
calling cpufreq_gov_dbs_init+0x0/0xb8 @ 1
initcall cpufreq_gov_dbs_init+0x0/0xb8 returned 0 after 3 usecs
calling cpufreq_gov_dbs_init+0x0/0xc @ 1
initcall cpufreq_gov_dbs_init+0x0/0xc returned 0 after 2 usecs
calling mmc_blk_init+0x0/0x7c @ 1
~~~~ hwftest driver_register: mmcblk
initcall mmc_blk_init+0x0/0x7c returned 0 after 3361 usecs
calling sdhci_drv_init+0x0/0x24 @ 1
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
initcall sdhci_drv_init+0x0/0x24 returned 0 after 7756 usecs
calling sdhci_drv_init+0x0/0xc @ 1
~~~~ hwftest driver_register: sdhci
initcall sdhci_drv_init+0x0/0xc returned 0 after 3267 usecs
calling vdoa_init+0x0/0x2c @ 1
~~~~ hwftest driver_register: mxc_vdoa
initcall vdoa_init+0x0/0x2c returned 0 after 3522 usecs
calling vpu_init+0x0/0x3c @ 1
~~~~ hwftest driver_register: mxc_vpu
initcall vpu_init+0x0/0x3c returned 0 after 3440 usecs
calling asrc_init+0x0/0x84 @ 1
~~~~ hwftest driver_register: mxc_asrc
initcall asrc_init+0x0/0x84 returned 0 after 3524 usecs
calling gpu_init+0x0/0xc @ 1
~~~~ hwftest driver_register: galcore
initcall gpu_init+0x0/0xc returned 0 after 3425 usecs
calling anatop_thermal_init+0x0/0xc @ 1
~~~~ hwftest driver_register: anatop_thermal
initcall anatop_thermal_init+0x0/0xc returned 0 after 4025 usecs
calling gpio_led_init+0x0/0xc @ 1
~~~~ hwftest driver_register: leds-gpio
initcall gpio_led_init+0x0/0xc returned 0 after 3594 usecs
calling gpio_trig_init+0x0/0xc @ 1
initcall gpio_trig_init+0x0/0xc returned 0 after 2 usecs
calling defon_trig_init+0x0/0xc @ 1
initcall defon_trig_init+0x0/0xc returned 0 after 2 usecs
calling caam_base_init+0x0/0xc @ 1
~~~~ hwftest driver_register: caam
initcall caam_base_init+0x0/0xc returned 0 after 3171 usecs
calling hid_init+0x0/0x6c @ 1
initcall hid_init+0x0/0x6c returned 0 after 226 usecs
calling hid_init+0x0/0x78 @ 1
~~~~ hwftest driver_register: generic-usb
~~~~ hwftest driver_register: usbhid
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
initcall hid_init+0x0/0x78 returned 0 after 13785 usecs
calling alsa_hwdep_init+0x0/0x64 @ 1
initcall alsa_hwdep_init+0x0/0x64 returned 0 after 9 usecs
calling alsa_timer_init+0x0/0x18c @ 1
initcall alsa_timer_init+0x0/0x18c returned 0 after 232 usecs
calling alsa_pcm_init+0x0/0x6c @ 1
initcall alsa_pcm_init+0x0/0x6c returned 0 after 6 usecs
calling snd_mem_init+0x0/0x44 @ 1
initcall snd_mem_init+0x0/0x44 returned 0 after 11 usecs
calling alsa_rawmidi_init+0x0/0x18 @ 1
initcall alsa_rawmidi_init+0x0/0x18 returned 0 after 1 usecs
calling snd_usb_audio_init+0x0/0x44 @ 1
~~~~ hwftest driver_register: snd-usb-audio
usbcore: registered new interface driver snd-usb-audio
initcall snd_usb_audio_init+0x0/0x44 returned 0 after 8727 usecs
calling mxc_hdmi_codec_init+0x0/0xc @ 1
~~~~ hwftest driver_register: mxc_hdmi_soc
initcall mxc_hdmi_codec_init+0x0/0xc returned 0 after 3873 usecs
calling mxc_spdif_init+0x0/0xc @ 1
~~~~ hwftest driver_register: mxc_spdif
initcall mxc_spdif_init+0x0/0xc returned 0 after 3598 usecs
calling cs42888_init+0x0/0x24 @ 1
Cirrus Logic CS42888 ALSA SoC Codec Driver
~~~~ hwftest driver_register: cs42888
i2c-core: driver [cs42888] using legacy suspend method
i2c-core: driver [cs42888] using legacy resume method
initcall cs42888_init+0x0/0x24 returned 0 after 16635 usecs
calling sgtl5000_modinit+0x0/0x10 @ 1
~~~~ hwftest driver_register: sgtl5000
initcall sgtl5000_modinit+0x0/0x10 returned 0 after 3513 usecs
calling wm8962_modinit+0x0/0x30 @ 1
~~~~ hwftest driver_register: wm8962
initcall wm8962_modinit+0x0/0x30 returned 0 after 3335 usecs
calling imx_ssi_init+0x0/0xc @ 1
~~~~ hwftest driver_register: imx-ssi
initcall imx_ssi_init+0x0/0xc returned 0 after 3427 usecs
calling imx_esai_init+0x0/0xc @ 1
~~~~ hwftest driver_register: imx-esai
initcall imx_esai_init+0x0/0xc returned 0 after 3518 usecs
calling imx_hdmi_dai_init+0x0/0xc @ 1
~~~~ hwftest driver_register: imx-hdmi-soc-dai
initcall imx_hdmi_dai_init+0x0/0xc returned 0 after 4215 usecs
calling snd_imx_pcm_init+0x0/0xc @ 1
~~~~ hwftest driver_register: imx-pcm-audio
initcall snd_imx_pcm_init+0x0/0xc returned 0 after 3938 usecs
calling hdmi_dma_init+0x0/0xc @ 1
~~~~ hwftest driver_register: imx-hdmi-soc-audio
initcall hdmi_dma_init+0x0/0xc returned 0 after 4362 usecs
calling imx_spdif_dai_init+0x0/0xc @ 1
~~~~ hwftest driver_register: imx-spdif-dai
initcall imx_spdif_dai_init+0x0/0xc returned 0 after 3957 usecs
calling imx_asoc_init+0x0/0x9c @ 1
~~~~ hwftest driver_register: imx-wm8962
#### hwftest platform_device_add(): soc-audio
Registering platform device 'soc-audio.5'. Parent at platform
~~~~ hwftest bus: 'platform': add device soc-audio.5
==== hwftest bus: 'platform': add device soc-audio.5 ok!

Registering platform device ==== add OK

initcall imx_asoc_init+0x0/0x9c returned 0 after 27055 usecs
calling imx_sgtl5000_init+0x0/0xac @ 1
~~~~ hwftest driver_register: imx-sgtl5000
#### hwftest platform_device_add(): soc-audio
Registering platform device 'soc-audio.1'. Parent at platform
~~~~ hwftest bus: 'platform': add device soc-audio.1
==== hwftest bus: 'platform': add device soc-audio.1 ok!

Registering platform device ==== add OK

initcall imx_sgtl5000_init+0x0/0xac returned 0 after 27210 usecs
calling imx_3stack_asoc_init+0x0/0x80 @ 1
imx_3stack asoc driver
~~~~ hwftest driver_register: imx-cs42888
#### hwftest platform_device_add(): soc-audio
Registering platform device 'soc-audio.2'. Parent at platform
~~~~ hwftest bus: 'platform': add device soc-audio.2
==== hwftest bus: 'platform': add device soc-audio.2 ok!

Registering platform device ==== add OK

initcall imx_3stack_asoc_init+0x0/0x80 returned 0 after 29164 usecs
calling imx_spdif_init+0x0/0xac @ 1
~~~~ hwftest driver_register: imx-spdif-audio-device
#### hwftest platform_device_add(): soc-audio
Registering platform device 'soc-audio.3'. Parent at platform
~~~~ hwftest bus: 'platform': add device soc-audio.3
==== hwftest bus: 'platform': add device soc-audio.3 ok!

Registering platform device ==== add OK

initcall imx_spdif_init+0x0/0xac returned 0 after 28063 usecs
calling imx_hdmi_init+0x0/0xa0 @ 1
Initialize HDMI-audio failed. Load HDMI-video first!
initcall imx_hdmi_init+0x0/0xa0 returned -19 after 4595 usecs
calling alsa_sound_last_init+0x0/0x6c @ 1
ALSA device list:
No soundcards found.
initcall alsa_sound_last_init+0x0/0x6c returned 0 after 3676 usecs
calling flow_cache_init_global+0x0/0x144 @ 1
initcall flow_cache_init_global+0x0/0x144 returned 0 after 92 usecs
calling llc_init+0x0/0x24 @ 1
initcall llc_init+0x0/0x24 returned 0 after 2 usecs
calling llc2_init+0x0/0xcc @ 1
NET: Registered protocol family 26
initcall llc2_init+0x0/0xcc returned 0 after 3166 usecs
calling snap_init+0x0/0x44 @ 1
initcall snap_init+0x0/0x44 returned 0 after 3 usecs
calling sysctl_ipv4_init+0x0/0x94 @ 1
initcall sysctl_ipv4_init+0x0/0x94 returned 0 after 475 usecs
calling xfrm4_beet_init+0x0/0x10 @ 1
initcall xfrm4_beet_init+0x0/0x10 returned 0 after 2 usecs
calling xfrm4_transport_init+0x0/0x10 @ 1
initcall xfrm4_transport_init+0x0/0x10 returned 0 after 1 usecs
calling xfrm4_mode_tunnel_init+0x0/0x10 @ 1
initcall xfrm4_mode_tunnel_init+0x0/0x10 returned 0 after 2 usecs
calling inet_diag_init+0x0/0x90 @ 1
initcall inet_diag_init+0x0/0x90 returned 0 after 14 usecs
calling tcp_diag_init+0x0/0xc @ 1
initcall tcp_diag_init+0x0/0xc returned 0 after 1 usecs
calling cubictcp_register+0x0/0x74 @ 1
TCP cubic registered
initcall cubictcp_register+0x0/0x74 returned 0 after 1892 usecs
calling packet_init+0x0/0x48 @ 1
NET: Registered protocol family 17
initcall packet_init+0x0/0x48 returned 0 after 3087 usecs
calling can_init+0x0/0xe8 @ 1
can: controller area network core (rev 20090105 abi 8)
NET: Registered protocol family 29
initcall can_init+0x0/0xe8 returned 0 after 7907 usecs
calling raw_module_init+0x0/0x38 @ 1
can: raw protocol (rev 20090105)
initcall raw_module_init+0x0/0x38 returned 0 after 2910 usecs
calling bcm_module_init+0x0/0x64 @ 1
can: broadcast manager protocol (rev 20090105 t)
initcall bcm_module_init+0x0/0x64 returned 0 after 4271 usecs
calling rfcomm_init+0x0/0x100 @ 1
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
initcall rfcomm_init+0x0/0x100 returned 0 after 9743 usecs
calling bnep_init+0x0/0xa8 @ 1
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
initcall bnep_init+0x0/0xa8 returned 0 after 7751 usecs
calling hidp_init+0x0/0x54 @ 1
Bluetooth: HIDP (Human Interface Emulation) ver 1.2
~~~~ hwftest driver_register: generic-bluetooth
initcall hidp_init+0x0/0x54 returned 0 after 8825 usecs
calling lib80211_init+0x0/0x20 @ 1
lib80211: common routines for IEEE802.11 drivers
initcall lib80211_init+0x0/0x20 returned 0 after 4261 usecs
calling lib80211_crypto_wep_init+0x0/0xc @ 1
initcall lib80211_crypto_wep_init+0x0/0xc returned 0 after 5 usecs
calling lib80211_crypto_ccmp_init+0x0/0xc @ 1
initcall lib80211_crypto_ccmp_init+0x0/0xc returned 0 after 6 usecs
calling lib80211_crypto_tkip_init+0x0/0xc @ 1
initcall lib80211_crypto_tkip_init+0x0/0xc returned 0 after 6 usecs
calling vfp_init+0x0/0x178 @ 1
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
initcall vfp_init+0x0/0x178 returned 0 after 6254 usecs
calling busfreq_init+0x0/0x80 @ 1
~~~~ hwftest driver_register: imx_busfreq
Bus freq driver module loaded
Bus freq driver Enabled
initcall busfreq_init+0x0/0x80 returned 0 after 8746 usecs
calling clk_debugfs_init+0x0/0xa0 @ 1
initcall clk_debugfs_init+0x0/0xa0 returned 0 after 2005 usecs
calling dvfs_init+0x0/0x4c @ 1
~~~~ hwftest driver_register: imx_dvfscore
DVFS driver module loaded
initcall dvfs_init+0x0/0x4c returned 0 after 6221 usecs
calling init_oops_id+0x0/0x4c @ 1
initcall init_oops_id+0x0/0x4c returned 0 after 13 usecs
calling printk_late_init+0x0/0x70 @ 1
initcall printk_late_init+0x0/0x70 returned 0 after 2 usecs
calling pm_qos_power_init+0x0/0xac @ 1
initcall pm_qos_power_init+0x0/0xac returned 0 after 685 usecs
calling max_swapfiles_check+0x0/0x8 @ 1
initcall max_swapfiles_check+0x0/0x8 returned 0 after 3 usecs
calling ubifs_init+0x0/0xc4 @ 1
initcall ubifs_init+0x0/0xc4 returned 0 after 455 usecs
calling random32_reseed+0x0/0xac @ 1
initcall random32_reseed+0x0/0xac returned 0 after 49 usecs
calling mxc_epdc_fb_init+0x0/0xc @ 1
~~~~ hwftest driver_register: imx_epdc_fb
initcall mxc_epdc_fb_init+0x0/0xc returned 0 after 3846 usecs
calling regulator_init_complete+0x0/0x130 @ 1
initcall regulator_init_complete+0x0/0x130 returned 0 after 5 usecs
calling random_int_secret_init+0x0/0x1c @ 1
initcall random_int_secret_init+0x0/0x1c returned 0 after 37 usecs
calling scsi_complete_async_scans+0x0/0x11c @ 1
initcall scsi_complete_async_scans+0x0/0x11c returned 0 after 2 usecs
calling cpufreq_interactive_init+0x0/0x1bc @ 1
initcall cpufreq_interactive_init+0x0/0x1bc returned 0 after 93 usecs
calling net_secret_init+0x0/0x1c @ 1
initcall net_secret_init+0x0/0x1c returned 0 after 36 usecs
calling tcp_congestion_default+0x0/0xc @ 1
initcall tcp_congestion_default+0x0/0xc returned 0 after 2 usecs
calling ip_auto_config+0x0/0xeb8 @ 1
initcall ip_auto_config+0x0/0xeb8 returned 0 after 15 usecs
calling mxc_early_uart_console_disable+0x0/0x40 @ 1
async_waiting @ 1
async_continuing @ 1 after 0 usec
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 58261504 bytes (56896 KiB, 55 MiB, 56 LEBs)
UBIFS: journal size: 8323073 bytes (8128 KiB, 7 MiB, 6 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 2751834 bytes (2687 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:12.
async_waiting @ 1
async_continuing @ 1 after 1 usec
Freeing init memory: 200K
#### hwftest ramdisk_execute_command = (null) execute_command=(null)
starting pid 1228, tty '': '/etc/rc.d/rcS'
Mounting /proc and /sys
Starting the hotplug events dispatcher udevd
udevd (1237): /proc/1237/oom_adj is deprecated, please use /proc/1237/oom_score_adj instead.
Synthesizing initial hotplug events
【此后无下文，或在这点出现oop信息】